Instruções de Instalação de software para WorkCentre M940-M950 * * * * * IMPORTANTE * * * * * Antes de instalar este software novo Desinstale qualquer software do WorkCentre M940-M950 clicando " começo/start ", " Programas ", " Xérox WorkCentre M940-M950 ", " Uninstall/Desinstale Xérox WorkCentre M940-M950 ". Ao Desinstalar a caixa de diálogo da Xérox WorkCentre M940-M950 tenha certeza que todos os artigos estão conferidos e clique " unistall/desinstalar". * * * * * IMPORTANTE * * * * * Se a nova tela de dilalogo do hardware aparecer antes do passo #14 remova a tomada electrica e o cabo de dados de seu M940-M950 e clique "cancel/cancelar". 1) Remova a tomada e o cabo de dados do M940-M950 2) No "Web Site" Drivers & Download clicar " uswxp124.exe " 3) Selecione "OK" 4) Selecione "Setup" 5) Selecione " Next/Proximo " 6) Responda o Acordo de Licença de Software com " Yes/Sim ou No/Não " 7) Selecione " Next/Proximo " para uma instalação Típica 8) Selecione " Next/Proximo " para escolher o destino 9) Quando você tiver o CD que veio com seu M940-M950 pronto, selecione OK ", então insira o CD 10) Selecione " Continue Anyway/Continue de qualquer maneira " e espere o software ser instalado 11) Remova o CD e clique " OK " 12) Selecione " Finish/Fim " para encerrar o seu PC. Isto pode levar vários minutos. 13) Conecte seu cabo de dados e o cabo electrico ao M940-M950. 14) Inicie o seu PC 15) Ignore a pequena tela de mensagens que aparecera mais abaixo ao lado direito da tela. Quando a " nova tela de dialogo do hardware encontrado " aparecer selecione " Next/Proximo " 16) Selecione " Continue " para continuar a instalar o software da M940-M950 em ambos os diálogos de Instalação de Hardware 17) Selecione " Next/Proximo " para obter o teste de Diagnóstico 18) Se qualquer dos testes de Diagnóstico falhar, confira todas as conexões de cabo e desligue o M940-M950 , espere 10 segundos, depois ligue novamente. Selecione " Back/Voltar " depois " Next/Próximo " repetir o teste Diagnóstico. Depois de duas tentativas se qualquer teste falhar selecione " Back/Voltar " depois " Skip/Salte " para completar instalação. 19) Selecione " Next/Proximo " 20) Selecione " Finish/Fim " 21) Selecione "Finish/Fim " na tela de dialogo do hardware encontrado 22) A Instalação do software do seu WorkCentre M940-M950 está completa Software Installation Instructions for WorkCentre M940-M950 ***** IMPORTANT ***** Before installing this new software Uninstall any WorkCentre M940-M950 software by clicking "start", "All Programs", "Xerox WorkCentre M940-M950", "Uninstall Xerox WorkCentre M940-M950." At the Uninstall Xerox WorkCentre M940-M950 dialog box make sure all items are checked and click "uninstall." ***** IMPORTANT ***** If the Found New Hardware Wizard dialog appears before step #14 remove the power plug and data cable from your M940-M950 and click "cancel." 1) Remove the M940-M950 power plug and data cable 2) At the Drivers & Download web site click on "uswxp124.exe" 3) Select "OK" 4) Select "Setup" 5) Select "Next" 6) Answer the Software License Agreement with "Yes or No" 7) Select "Next" for a Typical installation 8) Select "Next" at the choose Destination Location 9) When you have the CD which came with your M940-M950 ready, select "OK", then insert the CD when prompted 10) Select "Continue Anyway" and wait for the software to be installed 11) Remove the CD and click "OK" 12) Select "Finish" to shut down you PC. This may take several minutes. 13) Connect your data cable and power cord to the M940-M950. 14) Turn on your PC 15) Ignore the small pop-up messages at the lower right side of the display. When the "Found New Hardware Wizard" dialogue box appears select "Next" 16) Select "Continue Anyway" to continue installing the M940-M950 software at both of the Hardware Installation dialogues 17) Select "Next" to run the Diagnostic test 18) If any of the Diagnostic tests fail, check all cable connections and unplug the M940-M950 power cord, wait 10 seconds, then plug it in again. Select "Back" then "Next" to repeat the Diagnostic test. After two attempts if any test fails select "Back" then "Skip" to complete installation. 19) Select "Next" 20) Select "Finish" 21) Select "Finish" on the Found New Hardware Wizard dialogue box 22) Your WorkCentre M940-M950 software installation is complete